25b-554e011 manual

Troy - Bilt LLC reserves the right to change product specifications, designs and equipment without notice and without incurring obligation. You can locate the model plate by standing at the operatora??s position and looking down at the rear of the deck. This information will be necessary, se r ial n uM b e r should you seek technical support via our web site, Customer Support Department, or with a local authorized service dealer. Customer Support Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department. If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine, you can seek help from the experts. Choose from the options below: a?? Visit us on the web at www.troybilt.com a?? Call a Customer Support Representative at ( 800 ) 828 - 5500 or ( 330 ) 558 - 7220 a?? Write us at Troy - Bilt LLC a?? P.O. Box 361131 a?? Cleveland, OH a?? 44136 - 0019 2 Page: 3 Important Safe Operation Practices 2 WARNING. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.DANGER ! This machine was built to be operated according to the safe operation practices in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers, hands, toes and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Training Preparation 1. Read this operatora??s manual carefully in its entirety before 1. Thoroughly inspect the area where the equipment is to be attempting to assemble this machine. Read, understand, used.

• 25b-554e011 manual, troy bilt 25b-554e011 manual, troy bilt edger 25b-554e011 manual, 25b-554e011 manual, troy-bilt 25b-554e011 manual, 25b 554e011 owner manual.

Slowly slip starter rope into rope guide. Rope Secure handle by tightening hand knobs. Tighten rope guide wing nut.Oil Fill Set depth blade to highest position. Depress blade control handle and hold. Gas Cap Fill engine with entire contents of oil bottle supplied with your edger. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. PRINTED IN U.S.A READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION IMPORTANT OPERATOR’S MANUAL Edger — Model 554 FORM NO. 769-02162B How do you r. Sign up now. If you want to search this text, hold control and F, and type the word you are looking for. Page: 1 Safe Operation Practices a?? Set - Up a?? Operation a?? Maintenance a?? Service a?? Troubleshooting a?? Warranty O per atOr a?? s Manual Lawn Edger a?? Model 554 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.We want Please read this entire manual prior to operating the equipment.It instructs you how to safely and easily set up, operate and Throughout this manual, all references to right and left side of the maintain your machine. Please be sure that you, and any other machine are observed from the operating position persons who will operate the machine, carefully follow the recommended safety practices at all times. Failure to do so could The engine manufacturer is responsible for all engine - related result in personal injury or property damage.Review machine, for more information.Please be aware that this Operatora??s Manual may cover a range of product specifications for various models.

Remove gas - powered equipment from the truck or trailer and refuel it on the ground. If this is not 9. Do not operate this machine if it has been dropped or possible, then refuel such equipment on a trailer damaged. Return machine to your nearest authorized with a portable container, rather than from a servicing dealer for examination and repair.Keep the nozzle in contact with the rim of the fuel excessively worn cutting blade.Never attempt to clear material from the blade guard complete. Do not use a nozzle lock - open device.Shut the engine off, e. Extinguish all cigarettes, cigars, pipes and other disconnect the spark plug wire and ground against sources of ignition.Do not overload machine capacity by attempting to vapors will accumulate in the area.Stay alert for uneven sidewalks, terrain etc. Always hot or running. Allow engine to cool at least two push slowly over rough surfaces. Do not use this minutes before refueling.Fill tank to no more than A? 14. Do not operate machine in rain or wet soil conditions.Always operate machine from behind the handles expansion.Replace gasoline cap and tighten securely.Always stop engine when edging or trimming is equipment. Move machine to another area. Wait 5 delayed or when transporting machine from one minutes before starting engine.Never leave a running machine unattended. Stop open flame, spark or pilot light as on a water heater, the engine, disconnect spark plug wire and ground space heater, furnace, clothes dryer or other gas against the engine to prevent unintended starting.To reduce fire hazard, keep lawn edger free of grass, by the manufacturer. Failure to do so, can result in leaves, or other debris build - up. Clean up oil or fuel personal injury.Allow a lawn edger to cool at least five ( 5 ) minutes manual, use care and good judgment. Contact before storing.. Customer Support for assistance or the name of your nearest service dealer. Operation Children 1. Do not put hands or feet near rotating parts.

Remove all stones, sticks, wire, bones, toys and other and follow all instructions on the machine and in the foreign objects which could be tripped over or picked up manual ( s ) before operation. Keep this manual in a safe and thrown by the blade. Thrown objects can cause serious place for future and regular reference and for ordering personal injury.Be completely familiar with the controls and the proper use operation and while performing an adjustment or repair of this machine before operating it.Thrown objects which ricochet can cause serious injury to the eyes. 3. This machine is a precision piece of power equipment, not a plaything. Therefore, exercise extreme caution at all 3. Wear sturdy, rough - soled work shoes and close - fitting times. Your machine has been designed to perform one slacks and shirts. Shirts and pants that cover the arms job: to edge lawn. Do not use it for any other purpose.Never operate this machine in bare feet, sandals, slippery or light 4. Never allow children under 14 years of age to operate this weight ( e.g. canvas ) shoes. machine. Children 14 and over should read and understand the instructions and safe operation practices in this manual 4. Never attempt to make any adjustments while the engine and on the machine and be trained and supervised by an is running, except where specifically recommended in the adult.Gasoline is extremely flammable and the 6. To help avoid blade contact or a thrown object injury, vapors are explosive. Serious personal injury can occur when stay in operator zone behind handles and keep children, gasoline is spilled on yourself or your clothes which can ignite.Stop machine if anyone a. Use only an approved gasoline container.Always place containers on the ground away from your vehicle 8. Never operate this machine without good visibility or before filling. light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run. c.

Before cleaning, repairing, or inspecting, make certain the brushcovered or grass - covered land unless the blade and all moving parts have stopped. Disconnect the enginea??s exhaust system is equipped with a spark spark plug wire and ground against the engine to prevent arrester meeting applicable local or state laws ( if unintended starting. any ). 3. Check the blade and engine mounting bolts at frequent If a spark arrester is used, it should be maintained in effective intervals for proper tightness. Also, visually inspect blade working order by the operator. In the State of California the for damage ( e.g., bent, cracked, worn ) Replace blade with above is required by law ( Section 4442 of the California Public the original equipment manufacturea??s ( O.E.M. ) blade only, Resources Code ). Federal laws listed in this manual.Lawn edger blades are sharp and can cut. Wrap the blade department, P.O. Box 361131 Cleveland, Ohio 44136 - 0019.Check their proper operation regularly. 7. After striking a foreign object, stop the engine, disconnect the spark plug wire and ground against the engine. Thoroughly inspect the lawn edger for any damage. Repair the damage before starting and operating the lawn edger. 8. Never attempt to make a wheel adjustment while the engine is running. 9. Many components on your new edger can wear with continued use. For safety protection, frequently check all edger components and replace immediately with original equipment manufacturera??s ( O.E.M. ) parts only, listed in this manual.The governor controls the maximum safe operating speed of the engine. 11. Maintain or replace safety and instruction labels, as necessary. 12. Observe proper disposal laws and regulations for used gas, oil, etc.. Improper disposal of fluids and materials can harm the environment. WARNING ! Your Responsibility a?? Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

Contact with the rotating blade can amputate hands and feet. Tragic accidents can occur if the operator is not alert to the 2. The blade control handle is a safety device. Never bypass presence of children. Children are often attracted to power its operation. Doing so, makes the machine unsafe and may equipment such as lawn edgers. They do not understand cause personal injury.Never operate with damaged safety devices. Failure to do operator.Never run an engine indoors or in a poorly ventilated area. area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 3. Before and while moving backwards, look behind and down for small children. 6. Do not operate machine while under the influence of alcohol or drugs. 4. Use extreme care when approaching blind corners, doorways, shrubs, trees, or other objects that may obscure your vision of a child who may run into the lawn edger. 4 s ec t i O n 2 a?? i M p O r tan t sa fe O pe r at i O n pr ac t i ce s Page: 5 13. According to the Consumer Products Safety Commission 5. Keep children away from hot or running engines. They can ( CPSC ) and the U.S. Environmental Protection Agency ( EPA ), suffer burns from a hot muffler.Never allow children under 14 years of age to operate this or 70 hours of operation. At the end of the Average Useful machine. Children 14 and over should read and understand Life have the machine inspected annually by an authorized the instructions and safe operation practices in this manual service dealer to ensure that all mechanical and safety and on the machine and be trained and supervised by an systems are working properly and not worn excessively. adult. Failure to do so can result in accidents, injuries or death. Maintenance and Storage Spark Arrestor 1. Never run an engine indoors or in a poorly ventilated area. WARNING ! This machine is equipped with an Engine exhaust contains carbon monoxide, an odorless internal combustion engine and should not be used and deadly gas.

4. Once you have finished edging selected area, raise the blade control lever back into the START position, move to the next area to be edged, and proceed again from step 1. 9 Page: 10 Edging Along A Curb Beveling The right, rear wheel of the edger can be lowered into one of five In order to achieve a bevelled edge, set the bevel adjustment positions to ease the task of edging along a curb. Pivot the right, rear wheel into an applicable position in relation to the height of the curb to be edged along. See Fig. 5 a?? 2 3. Release the curb height adjustment lever to lock the wheel in position. See Fig. 5 a?? 2. 10 s ec t i O n 5 a?? O pe r at i O n Page: 11 Trenching ( If Equipped ) You can utilize the edgera??s optional trenching feature in order to create a wider cutting path for such things as laying wire for landscape lighting. WARNING ! Disconnect the spark plug wire and ground against the engine before performing the following steps. WARNING ! The edger blade is sharp. Wear leather work gloves to protect your hands when working around the edger blade. 1. Use two wrenches ( one wrench to prevent hex bolt head from spinning and the other to unthread the flange nut ) to remove flange nut that secures edger blade, leaving the edger blade in place. See Fig. 5 a?? 4. Tri - Star Blade Flange Nut Edger Blade Flat Washer Figure 5 - 4 2. Install the additional edger blade supplied with your machine and the flat washer. See Fig. 5 a?? 4. 3. Secure with the flange nut removed earlier. Use a torque wrench to tighten the flange nut to between 37 foot - lbs.Repeat first three steps if belt is pinched. Disconnect the spark plug wire and ground against the engine before performing any Lubricate the wheels and bearings at least once a season with a adjustment, repairs or maintenance. light oil. Also if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel Engine with light oil. Refer to the Engine Operatora??

s Manual packed with your Pivot Points edger for a detailed description of all engine - related service specifications. Lubricate the pivot points on the blade control bail, blade depth control lever, and if applicable, the blade adjustment lever, and Edger Blade curb height adjustment lever with light oil at least once a season. Wear leather Bearing Block work gloves to protect your hands when working Lubricate the bearing block every 25 hours or at least once a around the edger blade. season. Simply apply oil at each end of the cover plate. See Fig. 1. Use two wrenches ( one wrench to prevent the hex bolt 6 a?? 2. head from spinning and the other to remove the flange nut ) to remove the edger blade. Refer to Fig. 6 a?? 1. Flange Nut Flat Washer Lubricate Edger Blade Figure 6 - 2 Figure 6 - 1 2. Remove and discard the edger blade but retain the flange nut. 3. Install the replacement edger blade and the flange nut removed earlier. Use a torque wrench to tighten the flange nut to between 37 foot - lbs.Repeat the first three steps if the belt is pinched. 12 Page: 13 Off - Season Storage Observe the following when preparing the edger for long - term storage: 1. Clean and lubricate the edger thoroughly as instructed on the previous page. 2. Refer to the Engine Operatora??s Manual packed separately with the edger for engine manufacturersa??s storage instructions. 3. Coat the edger blade with chassis grease to prevent rusting and corrosion. 4. Store the edger in a dry, clean area. Do not store next to any corrosive materials, such as lawn fertilizer. 5. Coat the edger, especially any springs and bearings with a light oil or silicone spray. NOTE: When storing any type of power equipment in an poorly ventilated or metal storage shed, care should be taken to rustproof the equipment. Remove the spindle sheaves belt guard by removing the Belt Replacement two self - tapping screws which secure it to the blade plate assembly. See Fig. 7 - 2.

Locate the rope guide found on the right side of the upper instructed in the separate Engine Operatora??s Manual packed with handle. Loosen, but do NOT remove, the wing knob which your machine.Stand behind the edger and hold the blade control against the upper handle. 3. Gently pull the starter rope out of the engine. 2 WARNING ! The edger blade WILL rotate when the starter rope is pulled. NOTE: The starter rope will not pull out of the engine unless the blade control ( refer to Fig. 3 a?? 2 ) is depressed Figure 3 - 1 against the upper handle. 2. Tighten the hand knobs, which are located on both the left 4. Slip the starter rope through the top of the rope guide.Read Instructions carefully. WARNING ! Use extreme caution when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition. Be familiar with all the controls and depressed against the upper handle in order to operate the their proper operation. Know how to stop the edger. Releasing the blade control stops the engine and the machine and disengage it quickly. It is used to control the depth of the cut.Primer Bevel Adjustment Lever The primer is used to pump gas into the carburetor and aid in The bevel adjustment lever is located on the front, left portion starting the engine. Use it to start a cold engine, but do not use it of the edger, behind the edger blade. It is used to vary the angle to restart a warm engine after a short shutdown. Curb Height Adjustment Lever The curb height adjustment lever is found on the rear portion of the edger. When placed in an applicable notch, it aids in stabilizing the edger while edging grass along a curb. 8 Page: 9 Operation 5 Starting the Engine Edging To start the edgera??s engine, proceed as follows: WARNING. Rotating cutting blade may throw objects causing personal injury. Keep area clear of 1.

Attach the spark plug wire to the spark plug. Make certain bystanders and do not operate without guards in the metal cap on the end of the spark plug wire is fastened place.WARNING ! Do not lower blade if blade is over 2. Move the blade depth control lever back to the START concrete, asphalt, rocks or the like. Blade can strike position in the adjacent ( top ) notch.Depress the primer bulb three times, pausing two to three property damage.Doing so may result in a flooded engine. 4. Standing behind the edger, depress the blade control and hold it against the upper handle with your left hand. WARNING ! This control mechanism is a safety device. Never attempt to bypass its operation. 5. With your right hand, grasp the recoil starter handle and slowly pull the rope outward until engine reaches the start of its compression cycle ( the rope will pull slightly harder at this point ). 6. After slowly allowing the rope to recoil, pull the rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle throughout the entire stroke. 7. Allow the starter handle to slowly return to the eyebolt. NOTE: If the engine fails to start after three pulls, depress the primer an additional two times before pulling the starter rope again. Figure 5 - 1 Stopping The Engine To stop the edgera??s engine, release the blade control. 2. With blade control lever in START position, make a pass along area to be edged before proceeding to the next notch. The further forward blade depth control lever is moved, the deeper or lower the blade will cut into the ground. Several passes may be necessary to obtain the desired depth of cut. Do not lower blade more than one depth notch at a time without making a pass. 3. For best results, proceed slowly along the path being edged. Slowly moving edger back and forth through cutting area, again making sure to keep the left rear wheel on the hard surface and the blade in the cutting path, close to but not touching the edge of the hard surface.

Drive Belt NOTE: To aid in reassembly, note the orientation of the drive belt Belt Guard on the two idler pulleys and the engine flywheel pulley prior to performing the following steps. Refer to Fig. 7 - 1. Flange Luck Nut Engine Flywheel Pulley Figure 7 - 2 Engine Flywheel 4. Carefully remove the belt from off of the pulleys, again Pulley making sure to note the orientation of the belt. Discard the belt. See Fig. 7 - 2. Figure 7 - 1 5. 5. Working from the front of the edger, place the belt The edger drive belt is subject to wear and should be replaced if onto the spindle sheaves, route it back onto the two idler any signs of cracking, shredding or rotting are present. To replace pulleys, and then place it onto the engine flywheel pulley.Working in front of the edger, loosen the flange lock nut into the top pulley and the flat side of the belt is seated on top of frame, allowing the idler pulley assembly to pivot into the bottom pulley. See Fig. 7 - 2. slightly out from the frame. See Fig. 7 - 1. 6. Reinstall the spindle sheaves belt guard with the self 2. With your other hand, carefully reach under the rear of tapping screws removed earlier.NOTE: Make certain that the drive belt is seated correctly and that it is riding smoothly on the spindle sheaves and is not pinched between them. Repeat the first three steps if the belt is pinched. WARNING ! Never operate the edger without the spindle sheaves belt guard in place. 14 Page: 15 Troubleshooting 8 Problem Cause Remedy Engine fails to start 1. Dirty air cleaner 1. Refer to the Engine Operatora??s Manual 2. Engine needs to be primed 2. Push primer bulb two or three times. 3. Fuel tank empty 3. Fill tank with clean, fresh gasoline. 4. Stale fuel in gasoline tank 4. Drain gasoline and refill tank with clean, fresh gasoline. 5. Spark plug wire disconnected. 5. Connect the spark plug wire to the spark plug. 6. Spark plug fouled 6. Clean, adjust gap or replace spark plug. 7. Engine flooded 7. Refer to the Engine Operatora??

s Manual. Engine runs erratic 1. Spark plug wire loose 1. Connect and tighten spark plug wire. 2. Stale fuel in gasoline tank 2. Drain gasoline and refill tank with clean, fresh gasoline. 3. Vent in gas cap plugged 3. Clear vent of any debris. 4. Water or dirt in fuel system 4. Drain fuel tank. Refill with fresh fuel. 5. Dirty air cleaner 5. Refer to the Engine Operatora??s Manual. 6. Carburetor out of adjustment 6. Refer to the Engine Operatora??s Manual. Engine Overheats 1. Engine oil level low 1. Fill crankcase with proper oil. 2. Air flow restricted 2. Clean the area around the enginea??s cooling fins. 3. Dirty air filter 3. Replace the enginea??s air filter. 4. Carburetor not adjusted properly 4. Refer to the Engine Operatora??s Manual. Excessive Vibration 1. Edger blade bent or damaged 1. Replace edger blade. 2. Blade spindle bent or damaged 2. Contact an authorized MTD service dealer. Drive - belt Slips 1. Belt worn or stretched 1.This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operatora??s Manual g. Transportation charges and service calls.Troy - Bilt does not warrant this product for commercial use.Damage resulting from the installation or use the applicable period of express written warranty above as to the of any part, accessory or attachment not approved by Troy - Bilt for use parts as identified. No other express warranty, whether written or with the product ( s ) covered by this manual will void your warranty as oral, except as mentioned above, given by any person or entity, to any resulting damage.During the period of the warranty, the exclusive and workmanship for a period of thirty ( 30 ) days from the date of remedy is repair or replacement of the product as set forth above. purchase.

Normal wear parts include, but are not limited to items The provisions as set forth in this warranty provide the sole and such as: batteries, belts, blades, blade adapters, tines, grass bags, exclusive remedy arising from the sale. Troy - Bilt shall not be liable wheels, rider deck wheels, seats, snow thrower skid shoes, friction for incidental or consequential loss or damage including, without wheels, shave plates, auger spiral rubber and tires.Attachments include, but are not limited to items such as: or consequential damages, or limitations on how long an implied grass collectors and mulch kits.PROOF OF PURCHASE, through your local authorized service dealer. In no event shall recovery of any kind be greater than the amount of To locate the dealer in your area: the purchase price of the product sold. Alteration of safety features of In the U.S.A. the product shall void this warranty. These items may carry a IMPORTANT: Owner must present Original Proof of Purchase to separate manufacturera??s warranty. Refer to applicable manufac - obtain warranty coverage.Troy - Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136 - 0019; Phone: 1 - 866 - 840 - 6483, 1 - 330 - 558 - 7220 MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1 - 800 - 668 - 1238 GDOC - 100020 REV. Este producto cumple con las estrictas normas de seguridad del Outdoor Power Equipment Institute y de un laboratorio Por favor lea todo este manual antes de operar el equipo.Si tiene algA?n problema o duda Le indica cA?mo configurar, operar y mantener la mA?quina respecto a la unidad, llame a un distribuidor de servicio Troy - Bilt con seguridad y fA?cilmente. Por favor asegA?rese de seguir autorizado o pA?ngase en contacto directamente con nosotros. Para productos de diferentes modelos. Troy - Bilt LLC se reserva el derecho de un paquete por separado, junto con su unidad. Para encontrar la placa de modelo, colA?quese detrA?s de la unidad en la posiciA?n del operador y mire hacia la parte inferior de la secciA?

n trasera del chasis.En caso de tener problemas para montar este producto o de tener dudas con respecto a los controles, funcionamiento o mantenimiento del mismo, puede solicitar la ayuda de expertos. Lea y siga todas las instrucciones de este manual antes de poner en funcionamiento esta mA?quina. Si no respeta estas instrucciones puede provocar lesiones personales.Esta mA?quina es capaz de amputar dedos, manos y pies y de arrojar objetos. De no respetar las instrucciones de seguridad siguientes se pueden producir lesiones graves o la muerte. CAPACITACIA?N Preparativos 1. Lea con atenciA?n todas las instrucciones contenidas en 1. Guarde este manual en un lugar seguro las cuchillas.Los objetos arrojados que 3. Esta mA?quina es una unidad de equipo motorizado de rebotan pueden producir lesiones oculares graves.No la utilice para vestir camisa y pantalA?n para cubrir brazos y piernas y usar ningA?n otro fin. zapatos con puntera de acero. SA?lo se debe permitir usar esta mA?quina a individuos responsables y familiarizados con sus reglas de seguridad. La gasolina es 6. Para ayudar a evitar el contacto con la cuchilla o una sumamente inflamable y sus vapores pueden causar explosiones.No los toque. recubrimiento plA?stico. Coloque siempre los 8.Camine, c. Retire el equipo a gasolina del camiA?n o remolque nunca corra. Si esto no es posible, llene el 9.Nunca intente sacar material del protector de la cuchilla del recipiente en todo momento, hasta terminar si el motor estA.Apague todos los cigarrillos, cigarros, pipas y otras accidentalmente.Siempre empuje lentamente g. Nunca saque la tapa de la gasolina ni agregue sobre las superficies A?speras. No utilice esta mA?quina sobre combustible mientras el motor estA. No opere la mA?quina bajo la lluvia o en condiciones de dos minutos antes de volver a cargar combustible.Utilice solamente piezas y accesorios manufacturados otros aparatos a gas.Si no lo hace, pueden l.

Para reducir el riesgo de incendio mantenga la producirse lesiones personales. Si se presentan situaciones que no estA?n previstas en este acumulaciA?n de otros desechos. Limpie los derrames manual, sea cuidadoso y use el sentido comA?n. PA?ngase de aceite o combustible y saque todos los residuos en contacto con Asistencia al Cliente para solicitar ayuda embebidos de combustible.Si lo hace, la mA?quina se torna peligrosa y puede causar lesiones 1.Tenga extrema precauciA?n cuando se aproxime a esquinas personales.No cambie la configuraciA?n del regulador del motor 5. El regulador del motor o calientes. Mantenimiento y almacenamiento Amortiguador de chispas 1. Nunca encienda el motor en espacios cerrados o en una zona con poca ventilaciA?n. El escape del motor contiene A? ADVERTENCIA ! Esta mA?quina estA? equipada con monA?xido de carbono, un gas inodoro y letal.Antes de limpiar, reparar o inspeccionar la mA?quina, utilizada en un terreno agreste cubierto por bosque, compruebe que la cuchilla y todas las partes mA?viles se malezas o hierba ni cerca del mismo excepto que el hayan detenido. Inspeccione ademA?s visualmente la cuchilla mantener en condiciones de uso adecuadas.Es posible que existan leyes similares en otros piezas que no cumplen con las especificaciones del equipo estados. Las leyes federales se aplican en territorios federales. Envuelva la cuchilla departamento de servicios, Apartado Postal 361131 Cleveland, o utilice guantes y extreme las precauciones cuando Ohio 44136 - 0019.Nunca altere los dispositivos de seguridad. Controle ProtecciA?n Ambiental de los Estados Unidos ( EPA ), este periA?dicamente que funcionen correctamente.Si no lo hace, pueden producirse 8. Nunca intente ajustar una rueda mientras el motor estA.Afloje, pero NO retire, la perilla de aletas que unidad.PA?rese detrA?s de la unidad y sostenga el control de la cuchilla contra la barra superior. 3. Jale suavemente de la cuerda de arranque fuera del motor. 2 A? ADVERTENCIA !